NCS20032DR2G

Tillverkare:	onsemi
Produktkategori:	Operational Amplifiers – Op Amps
Antal kanaler:	2 Channel
GBP – Gain Bandwidth Product:	7 MHz
SR – Slew Rate:	8 V/us
Vos – Input Offset Voltage:	5 mV
Ib – Input Bias Current:	1 pA
Matningsspänning - Max:	5 V
Matningsspänning - Min:	1.7 V
Operating Supply Current:	325 uA
Output Current per Channel:	96 mA
CMRR – Common Mode Rejection Ratio:	90 dB
en – Input Voltage Noise Density:	20 nV/sqrt Hz
Paket / Fodral:	SOIC-8
Monteringstyp:	SMD/SMT
Shutdown:	No Shutdown
Lägsta driftstemperatur:	- 40 C
Maximal driftstemperatur:	+ 125 C
Serie:	NCS20032
Förpackning:	Reel
Förpackning:	Klippt tejp
Förpackning:	MouseReel
Amplifier Type:	Low Voltage Amplifier
Varumärke:	onsemi
In – Input Noise Current Density:	100 fA/sqrt Hz
Input Type:	Differential
Ios – Input Offset Current:	1 pA
Output Type:	Rail-to-Rail
Produkt:	Operational Amplifiers
Produkttyp:	Op Amps – Operational Amplifiers
PSRR – Power Supply Rejection Ratio:	100 dB
Fabriksförpackning Kvantitet:	2500
Underkategori:	Amplifier ICs
THD plus Noise:	0.01 %
Vcm – Common Mode Voltage:	1.7 V to 5.1 V
Enhetens vikt:	0,019048 oz

Mer information

Current Sense Amplifiers

onsemi Current Sense Amplifiers monitor current consumption, providing critical information that can assist in the safety and diagnostic functions in a system. These Current Sense Amplifiers minimize BOM space and allow for system flexibility. They are low-cost, highly accurate, power-efficient, and offer minimal impact to battery life. onsemi offers cost-effective standalone Op-Amps and Current Sense Amplifiers that integrate external resistors to offer higher accuracy, smaller solution.

NCx2003x Operational Amplifiers

onsemi NCx2003x Operational Amplifier offers low 1.8V operation with a high slew rate and rail-to-rail output drive ability. A fast slew rate and wide unity-gain bandwidth of 5MHz at 1.8V make the NCx2003x op amp ideally suited for high-speed applications. The low input offset voltage of 4mV maximum allows designers to use the NCx2003x op amp for current shunt monitoring. The low 1.8V operation also enables high performance in low voltage, low-power applications. onsemi NCx2003x op amp also provides an ultra-low 1pA input bias current and no output phase reversal for overdriven inputs signals. The series is AEC-Q100 Qualified and PPAP capable, allowing designers to use the NCx2003x op amp in motor control drives, hard drives, medical devices, white goods, and air conditioners.

High Performance CMOS Operational Amplifiers

onsemi High-Performance CMOS Operational Amplifiers feature a wide range of general-purpose, low-power, and precision single, dual, and quad devices. The CMOS Op-Amps have the advantage of lower power and higher accuracy operation over traditional bipolar amplifiers, especially in terms of input bias current, quiescent current, and input offset voltage.

Industrial Motor Drives

onsemi Industrial Motor Drives are designed for global sustainability, supplying efficient, renewable technologies and intelligent power. According to the 2020 Motor System Market Analysis (MSMA), published by the US Department of Energy (DOE), industrial pumps and drives annually consume almost 15% of the total US grid. The 2020 MSMA also estimates that 32.3 million metric tons of CO₂ emissions can be saved annually using VFDs. onsemi manufactures a broad range of VFD semiconductor components, including gate drivers, MOSFETs, IGBTs, and EliteSiC.

NCS200x Rail-to-Rail Operational Amplifiers

onsemi NCS200x Rail-to-Rail Operational Amplifiers provide rail-to-rail output operation, and are available in single, dual, and quad configurations. Rail-to-rail operation enables the user to make optimal use of the entire supply voltage range while taking advantage of bandwidth. onsemi NCS200x can operate on supply voltages from 1.8V to 5.5V over the temperature range of −40°C to +125°C.

Recensioner

Det finns inga recensioner än.